IBM C9010-022 Exam Questions And Information – (DEC-2017 Dumps)

By | December 18, 2017

Do not bother with hunting for IBM C9010-022 Exam preparation material on different websites and training manuals. Use our IBM AIX Administration V1 C9010-022 Exam Dumps material for a step-by-step approach to learning and tackle easy–to-difficult C9010-022 exam questions in a systematic manner. Our experts have enumerated all possible C9010-022 exam questions with answers which you may encounter during the AIX V1 C9010-022certification exam.

C9010-022 PDF dumps; C9010-022 exam dumps:: https://www.dumpsschool.com/C9010-022-exam-dumps.html (62 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate IBM C9010-022 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

A system dump has been initiated on an LPAR and LED code “0c1” is displayed, indicating an I/O error. Where can the administrator find out more about this error?

A. The HMC Service Guide
B. The AIX Version 7.1 Commands Reference
C. HMC Event Log
D. IBM’s Fix Central under Power Systems LED support page

Answer: D

Question: 22

Given the following characteristics, tuning which resource will provide the greatest benefit?
CPU=80% busy
Physical Memory=90% used
Disks=80% busy
Network=80% used
Filesystemsare90%full.

A. Memory
B. Network
C. Disks
D. Filesystems

Answer: C

Question: 23

New Updated C9010-022 Exam Questions C9010-022 PDF dumps C9010-022 practice exam dumps: https://www.dumpsschool.com/C9010-022-exam-dumps.html

A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the administrator is trying to determine why it cannot be used to reach any other system on the network. He suspects that it may be caused by a problem in the VLAN configuration.
How would the administrator determine the VLAN for which the adapter was configured?

A. Use the command ‘Isdev -I ent0’ on the host to determine the port VLAN ID.
B. Use the command ‘Isattr-EI ent0’ on the host to determine the port VLAN ID.
C. Look on the HMC to determine which VLAN is configured for the adapter.
D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the adapter is using.

Answer: C

Question: 24

How can an administrator disable Role Based Access Control (RBAC) in a WPAR?

A. Run chattr -E -I sys0 -a enhanced_RBAC=false
Reboot the WPAR
B. Run the RBAC wizard and deselect ‘Enable RBAC
Reboot the system
C. Run chdev -I mywpar -a enhanced_RBAC=false
Reboot the Global Environment
D. Run chwpar -a RBAC=false
Reboot the WPAR

Answer: C

Question: 25

After performing a NIM rte install, the administrator noticed that not all filesets are at the correct Technology Level (TL). What action will help the administrator determine why the inconsistent fileset levels were installed?

A. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.
B. On the NIM client, run oslevel command against the TL to identify missing prerequisites.
C. Run instfix command on NIM client to determine what filesets are inconsistent.
D. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the lpp_source.

Answer: D

Question: 26

What is a requirement for Live Partition Mobility?

A. The network and disk must be virtual.
B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.
C. The client partition must be connected to a SAN.
D. The client partition must be set up as a ‘Mover Service Partition’.

Answer: A