Cisco 300-360 Exam Questions And Information – (DEC-2017 Dumps)

By | December 18, 2017

Do not bother with hunting for Cisco 300-360 Exam preparation material on different websites and training manuals. Use our Cisco Designing Cisco Wireless Enterprise Networks 300-360 Exam Dumps material for a step-by-step approach to learning and tackle easy–to-difficult 300-360 exam questions in a systematic manner. Our experts have enumerated all possible 300-360 exam questions with answers which you may encounter during the Cisco Certified Network Professional Wireless 300-360certification exam.

300-360 PDF dumps; 300-360 exam dumps:: https://www.dumpsschool.com/300-360-exam-dumps.html (83 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-360 Dumps Exam Questions and Answers:

Version: 9.0
Question: 21

An engineer is assigned to provide wireless coverage in a provincial capital building. Due to the age and historic nature of the building, the ability to run new copper Ethernet cable to desired AP locations is limited. Which requirement should the engineer specify to overcome this restriction?

A. Deploy access points where the survey indicates and connect them via fiber optic cable, using a mediaadapter, and locally provide power.
B. Deploy access points to each phone location converting two spare pairs of copper from the phone line toEthernet and locally provide power.
C. Deploy access point devices where limited cable can be run or exists and connect high-gain antennas andincrease Tx power to increase cell size.
D. Deploy RAP where limited cable can be run or exists, and extend coverage using MAP.

Answer: D

Question: 22

Which two steps are associated with the active portion of the audit when a post-installation audit is performed with an auditing tool such as Ekahau? (Choose two.)

A. Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel.
B. Verify smooth roaming.
C. Check to see if the signal level on other access points that are heard on the same channel is at least 19dBm weaker than the access point that you are next to.
D. Check that all channels are supported by the APs, regardless of client capabilities.
E. Verify that the network traffic of physical data rate and packet loss meets user requirements.

Answer: BE

Question: 23

New Updated 300-360 Exam Questions 300-360 PDF dumps 300-360 practice exam dumps: https://www.dumpsschool.com/300-360-exam-dumps.html

An engineer is preparing for an indoor wireless LAN survey and is provisioning a survey kit. Which three pieces of equipment should be included? (Choose three.)

A. external connector access point
B. integrated antenna access point
C. coax low-loss cable
D. battery operated power supply
E. range finder
F. Yagi antennas

Answer: BDE

Question: 24

Which three options are benefits of U-APSD? (Choose three.)

A. optimized power-save mode periods
B. increased call capacity
C. bandwidth reservation
D. synchronization of the transmission and reception of voice frames
E. efficient roaming
F. priority bandwidth and polling

Answer: ABD

Explanation:
Unscheduled automatic power-save delivery (U-APSD) is a feature that has two key benefits:
The primary benefit of U-APSD is that it allows the voice client to synchronize the transmission and reception of voice frames with the AP, thereby allowing the client to go into power-save mode between the transmission/reception of each voice frame tuple. The WLAN client frame transmission in the access categories supporting U-APSD triggers the AP to send any data frames queued for that WLAN client in that AC. A U-APSD client remains listening to the AP until it receives a frame from the AP with an end-of-service period (EOSP) bit set. This tells the client that it can now go back into its power-save mode. This triggering mechanism is considered a more efficient use of client power than the regular listening for beacons method, at a period controlled by the delivery traffic indication map (DTIM) interval, because the latency and jitter requirements of voice are such that a WVoIP client would either not be in power-save mode during a call, resulting in reduced talk times, or would use a short DTIM interval, resulting in reduced standby times. The use of U-APSD allows the use of long DTIM intervals to maximize standby time without sacrificing call quality. The U-APSD feature can be applied individually across access categories, allowing U-APSD can be applied to the voice ACs in the AP, but the other ACs still use the standard power save feature.
The secondary benefit of this feature is increased call capacity. The coupling of transmission buffered data frames from the AP with the triggering data frame from the WLAN client allows the frames from the AP to be sent without the accompanying interframe spacing and random backoff, thereby reducing the contention experience by call.
Reference: http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/vowlan/41dg/vowlan41dg-book/ vowlan_ch2.html#wp1045982

Question: 25

A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?

A. Deploy the specified access points per area type.
B. Resurvey and adjust the design.
C. Increase the Tx power on incorrectly surveyed access points.
D. Deploy unsurveyed access points to the design.

Answer: B

Question: 26

An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services. Which two requirements are inputs to the design? (Choose two.)

A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access pointE. continuous -72 dBm coverage from one access point

Answer: BD

http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob73dg/emob73/ ch3_WLAN.html#pgfId-1000250